CGI Door Installation Nationwide | TruePane Windows & Doors

CGI Door Installation: The Miami Beach Owner’s Guide

CGI door installation in Miami Beach typically runs $850 to $2,400 for a full replacement hung and sealed, with most jobs completed in a single visit. The part you’re likely hunting for is the CGI door panel itself, a hinge assembly, or the weatherstripping channel that has finally given out after years of salt air and sun. Owners usually discover the problem the same way: the door starts binding at the top corner in August, or water beads along the threshold after a hard rain off Biscayne Bay. We stock the common CGI door installation components on our trucks and can match most models within a day.

Call (386) 406-9359

TruePane Windows & Doors is an independent service provider, not affiliated with CGI. We carry and install genuine CGI parts alongside quality aftermarket equivalents, and we’ll show you the difference on paper before any work begins. If the pane is not true, the job is not done.

Key Takeaways

• CGI door installation in Miami Beach runs $850 to $2,400 installed, depending on panel size and hinge condition.
• We stock CGI-compatible door hardware and weatherstripping on the truck for most single-day jobs.
• Salt corrosion and thermal expansion are the two biggest killers of CGI door installations in Miami Beach.
• Free estimate, written line-item quote, and both warranty layers registered before our truck leaves your driveway.

Which CGI Models This Applies To

CGI’s residential door lines in South Florida break down into a few families: the Estate Collection, the Tribute Series, and the older Classic models that are still in thousands of Miami Beach homes from the mid-2000s build boom. Within each family, the door panels share hinge geometry but not always the same hinge pitch. The Tribute Series uses a different hinge offset than the Estate Collection, and mixing them up is exactly the kind of mistake that leaves a door swinging proud of the jamb by an eighth inch. If you have the original window or door sticker still taped to the hinge-side frame, that label will list the series and the panel size. No sticker? Measure the slab height and width at three points, then check the hinge center-to-center spacing. We can identify the series from that every time.

For Miami Beach specifically, genuine CGI parts carry a premium, but the aftermarket equivalents we stock are sourced from the same Florida contractors who supply the PBSO-approved and impact-rated market. For hinge pins and roller assemblies, a quality aftermarket part often outlasts the OEM in salt exposure because the coating is thicker. For the door panel itself, we recommend genuine CGI. It’s not snobbery. The panel is the structural component, and mixing a generic panel into a CGI jamb can void the manufacturer’s warranty on the opening. We’ll quote both and you decide with the numbers in front of you.

Signs Your CGI Door Installation Is Failing

• Binding at the top corner in summer. The hinge-side jamb has settled or the hinges have developed play. In Miami Beach, the underlying cause is usually thermal expansion combined with hinge pin wear. The fix is hinge replacement and a jamb alignment, not planing the slab.
• Water pooling at the threshold after heavy rain. The CGI threshold channel has a weep system that clogs with salt crust and fine sand. Once the weeps are blocked, water backs up under the sweep and into the house. We clean the channels, replace the sweep, and re-seal the threshold to the slab.
• A latching mechanism that sticks or fails. CGI doors use a multi-point lock system, and the keep inserts wear out first. When the lock throw starts to grind, you’re about two months from a door that won’t secure. That’s a common part; we replace the keeps and the lock body as a set.
• Sag at the strike side, visible as an uneven gap. The top hinge has taken the majority of the door’s weight for too long. Hinge leaf screws in older Miami Beach installations often corrode inside the jamb and back out slowly. We rebuild the screw pockets, replace damaged hinge leaves, and re-set the slab square.
• Bubbling or peeling along the bottom rail. Not cosmetic. The factory coating has been breached and the aluminum underneath is oxidizing. For a CGI door in Miami Beach salt air, this is a warning that the panel’s weather barrier is failing. Depending on the depth, it’s either a refinish or a panel replacement.

Replacement Cost & What’s Included

CGI door installation in Miami Beach breaks down like this:

• Hinge replacement (set, installed): $220-$480
• Threshold and sweep replacement: $180-$390
• Multi-point lock rebuild: $290-$560
• Full door panel replacement (hung and sealed): $850-$2,400

The range depends on panel size, series, and the condition of the jamb. A door that hasn’t been maintained for a decade usually needs hinge work and a new threshold at the same time. Every quote is a written line item. You’ll see the part cost, the labor, and the difference between OEM and aftermarket where applicable. No change orders, no surprise line items. Dale Kessler and our team price the job the first time, correctly, and The Keystone Standard means both warranty layers are registered in writing before we leave. The workmanship is covered for 90 days under our Done Right Promise, no arguing.

DIY or Call Us?

If you’re replacing a door sweep or cleaning the threshold weep channels, that’s a Saturday afternoon job with a screwdriver and patience. If the door is binding, sagging, or the lock isn’t engaging, stepping in with a pry bar is where things go wrong. CGI doors are heavy, the hinges are under constant load, and prying a slab out of the opening without releasing the tension properly can leave you with a cracked jamb and a door you can’t rehang alone. The multi-point lock is the safest part to leave alone entirely; the latch points have to align perfectly or the door either won’t lock or won’t open when you need it to. We’re fast at this because we’ve done hundreds of them across Miami Beach. Call (386) 406-9359 and we’ll get an estimate scheduled before you buy a part you might not need.

FAQs