Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMr-Glass Window Installation: The Miami Beach Owner’s Guide
If you have a Mr-Glass window that needs a new installation, we stock the hardware, glaze, and weather-sealing components to get it set right, and we do the work ourselves. An installed replacement in Miami Beach typically runs $220 to $480 for standard Mr-Glass frame units, depending on size and whether we are rebuilding the rough opening or just re-setting the sash. Most owners figure out something is wrong when the window starts binding, the seal fogs, or salt air has worked its way into the frame and the glass feels loose in the sash. The good news is a Mr-Glass window is straightforward to work on once you understand the frame channel and what Miami Beach’s salt air does to untreated aluminum over two or three hurricane seasons.
Which Mr-Glass Models This Applies To
We install and re-set parts for the Mr-Glass horizontal sliders, single-hung aluminum frames, and the impact-rated versions most common in Miami Beach condos built between 1985 and 2010. The easiest way to identify your unit is to look in the lower corner of the frame channel. Mr-Glass stamps a two-letter series code there, usually MG-SL for sliders or MG-SH for single-hung, followed by a four-digit size reference. We match that stamp. If the stamp is worn off, we measure the glass thickness and the depth of the frame channel on site.
One thing worth knowing about Mr-Glass parts: the factory used two different channel depths across their aluminum lines, and an installer who grabs the wrong depth will shim the frame into a bind that shows up in August when the aluminum expands. That is exactly the kind of mistake Dale Kessler grew up seeing in the Normandy Isles section of Miami Beach, and it is why we measure every opening twice before quoting. As for OEM versus aftermarket, we carry both. The aftermarket replacement frames we stock use the same marine-grade aluminum and low-E glass specs, and they cost about twenty percent less than a factory-ordered Mr-Glass component. We will quote either on paper, side by side, so the decision is yours.
Signs Your Mr-Glass Window Installation Is Failing
- Fogged glass between the panes. That is a failed thermal seal. In Miami Beach, the seal usually gives out after the frame has flexed through a few humid summers and a couple of storms, and moisture has started working on the desiccant strip.
- The sash binds when you slide it. This is almost always a channel-depth mismatch or a frame that was shimmed out of square. When aluminum expands in July heat, the bind gets worse.
- Water staining on the drywall or sill. The weep system in a Mr-Glass frame gets clogged with salt and fine sand, and water backs up instead of draining out. Left alone, it rots the rough opening.
- The glass rattles in the frame. The glazing gasket has hardened and shrunk from sun exposure. The glass can shift enough to break under wind load.
- Condensation inside the house on the glass surface in the morning. That is not always a seal failure; sometimes it is a frame that was not weatherproofed against Miami Beach’s interior humidity, so warm moist air is hitting a cold interior pane.
Replacement Cost & What’s Included
The installed price for a Mr-Glass window installation in Miami Beach generally falls between $220 and $480, with the glazing, the gasket set, and any new fasteners or shims included in the quote. Large impact-rated units or rebuilds where the rough opening has water damage can push that higher, and we will tell you honestly before we touch anything. The factors that move the number are the channel depth, whether the opening is still square, and whether the existing frame can be re-glazed or has to be replaced outright. Every quote is parts and labor together. We register both warranty layers in writing before the truck leaves your driveway, and the workmanship on any re-set or replacement is covered by our Done Right Promise. If the pane is not true, the job is not done.
DIY or Call Us?
You can safely check a few things yourself. Look at the series stamp in the frame channel. Try sliding the sash. Run a finger along the bottom track for grit and salt buildup. Those checks tell us a lot before we arrive. What we would not advise is pulling the sash out of a Mr-Glass aluminum frame. The extruded channel can deform if you lever it the wrong way, and then you are buying a new frame instead of a gasket. This is not high-tension work like a garage door spring, but it is still the kind of job where a small mistake costs more than the service call. If you want us to match the part and do the install, call (386) 406-9359 and talk to a live person. We will be there when we say, with a background-checked technician who has done this exact job in Miami Beach more times than we can count.
FAQs
In this climate, a properly set Mr-Glass window installation should last fifteen to twenty years before the seal or gasket starts to fail. The salt air and high humidity near the Intracoastal are brutal on seals, so windows that are driven by storm winds and heat cycles will sit at the lower end of that range. Call (386) 406-9359 if you want us to take a look at yours and give you an honest read on its remaining life.
In many cases, yes. If the frame channel is square and the aluminum is not pitting, we can re-glaze the unit and replace the gasket set and the weep system, which costs less than a full replacement. We will tell you straight if the frame has been flexed too far to trust, because putting new glass in a compromised frame is a waste of your money.
A standard single-hung or slider re-set usually takes two to three hours on site, from the time we take the first measurement to the time we wipe down the sill. If the rough opening needs repair, that adds time, and we will tell you before we start the clock. We schedule the job as a single visit because that is the only way we work.
We stock the most common Mr-Glass channel depths, gasket sets, weep covers, and low-E panels in our service truck, along with PGT, CGI, and CWS replacement parts for jobs that need them. If you have an unusual size, we will order the part and you will know the lead time before you pay anything. Call (386) 406-9359 and we will check what is on the truck right now.
Get Your Mr-Glass Window Installation Done Right
We have been setting windows in Miami Beach for more than two decades, and a Mr-Glass window installation is the kind of job we would rather get right the first time than revisit. Call (386) 406-9359 and tell us the series stamp on your frame and what the window is doing that it should not be doing. We will quote you the part and the labor upfront, in writing, with no surprises on the bill. If it is not right in the opening, it is not right, and we will stand behind the work until you are sure it is.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Miami Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.